New from T&J Performance Center are these heavy-duty diff covers for Dana 30, 35, and 44 axles. While providing greater protection against rocks and other hazards, the extra 1/8-inch steel plating along the bottom of the cover also acts as a skid plate to make getting past obstacles much easier.

Steering box brace for 1984 to 2001 Jeep XJ Cherokees. A bolt on kit that allows the sway bar to stay in the stock location. The heavy duty design helps eliminate steering slop and prevents cracks at the box mounting points.

his kit upgrades the basic Stage I Stiffener System by incorporating a skid that protects the unibody between the four major suspension pivots. The skid will help to decrease the chance of crushing the unibody and at the same time adds additional strength. This kit is recommended for the serious "off roader" or anybody who feels that their rig needs a lot more protection.

The ZJ Frame Stiffener System was designed in response to the growing number of our customers who drive ZJ Cherokees. This system makes use of quality MIG welded, 120 wall tubing and can be easily welded to your Cherokee. The basic idea behind our ZJ Frame Stiffener is to reinforce the unibody by providing high strength steel bars that run along the bottom of the unibody and tie into the suspension.

Conversion Shock Brackets for the front of the 1984 to 2001 Cherokees. This bracket bolts into the factory upper shock location and conversts the mount from a stem system to universal eyte mount. The kit will accommodate Bilstein, King, Swayaway, or Rancho shock absorbers.

1984 to 2001 Cherokee interior bar kit. This kit is the perfect starter kit whether you are racing a JeepSpeed or going slow wheeling. Our system is made of 1.75 x 1.20 wall cold roll tubing and consists of (2) A pillars, (1) B hoop, (1) windshield bar, (2) diagonal kickers, (2) side impact bars and (12) floor mounting plates.

The Barnett Performance Clutch Rod Kit replaces your Jeeps stock clutch linkage rods, with stainless steel rods that utilize heavier Hiem joint pivots at each end. Thus assuring a non wearing pivot and exact, consistent engagement of the clutch.

Our D-30 Gussets help add piece of mind and strutural integrity to your high priced differential housings. Complete with c-flange and upper/lower control arm gussets, this kit aids in protecting and strengthening the most vital parts of the front differential housing. Each gusset is made from high strength, cold roll, mild steel and are ready to be welded to your ride.

The CJ and YJ, S-link is the latest and greatest in our Barnett Performance line of products. The basic idea behind the revolutionary S-Link is to provide a rerouted tie rod that is bent in such a way that it completely bypasses the leafs springs in a spring over system. Problems like bump steer and steering slop are greatly reduced when you install the S-Link.

T and J Performance Center has been performing engine swaps in jeeps for many years. The owners of T and J, Mike and Tom Barnett found that no engine conversion just bolts in. In response to many letters the brothers have painstakinly engineered thier Barnett Performance Products, universal, cut to fit, engine mounts for the small block Chevy 350.

Barnett Performance has just introduced this Rear Universal Bump-stop Kit for the XJ.

Our Rear Adjustable Bump Stop Bracket Kit, in conjuntion with our front bracket kit provides superior ride adjustability for your off-road vehicle. These Brackets are fully MIG welded from quality cold roll steel.

Our Front Adjustable Bump Stop Brackets can easily be welded and bolted into the factory bump stop location. These bump stop brackets are made from the highest quality materials and accommodate a variety of after market bump stops.

This incredible system replaces your existing slip yoke with a bolt on kit which leaves your oil seal completely protected. Another awesome feature about our conversion kit is that it allows you to leave your transmission skid plate in its factory location when you do a suspension lift.

These tricked out gauge pods are made from fully worked aluminum to add a great look to your vehicles interior. Our gauge pods can accommodate four of your most vital gauges. This product provides a functional gauge carriage as well as a sweet look for your ride.

These stronger than life shock tabs are made of the same high strength cold roll steel that we use for all of our parts. Our paired kits are available in three sizes and can be used to mount shocks under roll cages, to axle housings, or anywhere you need the job done right.

Barnett Performance designed these universal threaded bungs in the right and left hand threads. The chromoly bungs allow you to fabricate Universal steering rods, adjustable linkages, or anything you want removable and tunable. Available in cut to order sizes, these bungs are just what you're looking for.

Introducing the newest addition to our Barnett Performance line of products. The Barnett Performance Products Rock Slider Protection System. This kit utilizes quality components and intricate MIG welding, to give you the kind of durability you have come to expect from the Barnett Performance name.

Check this out! Barnett Performance Products is proud to introduce to you, the XRock Sway Bar Kit For Your 84-01 Jeep Cherokee. Consisting of a Chromoly Mounting Tube and high strength, heat treated steel Torsion Bar, this kit takes the beating. The XRock kit eliminates the factory sway bar to give you better suspension articulation and adjustability without hampering on highway performance. This kit includes everything you need for a simple bolt in installation. No Welding Required!

Includes a custom fabricated square tube that parallels the body and has attachment tubes that weld to the frame for maximum load bearing support. Kit also includes the BP slider/step bar system that is welded on to the square slider tube.